Bogen PCMTIM Specifiche

PCM Paging Control SystemInstallation and Use Manual© 1999 Bogen Communications, Inc.All rights reserved. 54-2011-01 9910Model: LUPCMALLPEC Code: 532

Figure 4-1: LUPCMALL Feature Callouts[10]

[11]Descriptions and LocationsRefer to Figure 4-1.1. TEL INT SEL Switch Bank - Sets telephone interface type for the TEL LINE jack on the PCMTIM modul

[12]15. TALK BACK Switch Bank - Determines if a 70V speaker zone will operate as a two-way hands-free talk backzone or as a one-way paging zone (see S

❑5.System Wiring Connections5.1. Telephone System ConnectionsThe PCMTIM module is the telephone interface module for the PCM Paging Control System. Th

IMPORTANT: The polarity of the Tip & Ring contacts of the RJ11 jack for the Tel Line and Over Ride were chosenso that when a standard modular cord

4. Use 24-gauge solid wire to connect the GND ST terminal on the module to the PBX ground. This is typically theAC ground for the PBX system.IMPORTANT

The unit will also respond to CPC pulses (short losses of loop current). When a CPC pulse is detected, the unit willimmediately drop the line.1. Make

The night ringer normally sounds a simulated ring tone but can be programmed to sound a chime tone. Refer toSystem Programming, Section 11 to set up a

[18]

[19]6. Paging Amplifier ConnectionsThe paging amplifier audio connections are made to the PCMTBM module terminal strip. If the amplifier has apaging

© 1999 Bogen Communications, Inc.All Rights Reserved. Printed in U.S.A.NoticeEvery effort was made to ensure that the information in thisguide was com

[20]

The PCM system is very flexible in how it can provide background music throughout the system:• Background music can be continuously supplied to all zo

[22]

7.2. Background Music Continuously Supplied To All Zones Not Being PagedSee Figure 7-1 on page 20 for connection with a high-powered background music

[24]

[25]

[26]

[27]

[28]This page intentionally left blank

[29]8.1. Wiring to 70V SpeakersSee Figure 8-2 on page 30 for wiring.NOTE: Make sure PCMZPM OUTPUT switch is set to HI PWR. To set the switch, remove t

[3]Contents1. Introduction...5

Figure 8-2: Zone Wiring to Speakers[30]

[31]

Figure 9-1: Connection of Relays to the Relay Driver Outputs[32]

[33]9.1. CPU to Emergency SignalingExternal input control is available to trigger a tone signal from the PCM over the paging system. Shorting EM/SC to

[34]This page intentionally left blank

[35]10.1. Power-Up SequenceAll equipment in the paging system should remain off until the system wiring is completed. This is the recommendedpower-up

[36]This page intentionally left blank

[37]System programming lets you set certain PCM options and tone features using the DTMF keys of a telephone. Italso lets you to program paging zone g

[38]11.1. Programming Paging Zone Groups32 paging zone groups can be created. Each zone group can consist of up to 99 zones. To create a zone group:1.

[39]11.6. Single Amp BGM EnableSingle amplifier BGM operation lets the PCM use the paging amplifier to provide high-powered BGM to passivespeakers whe

[4]8. Zone Speaker Wiring and Setup ...318.1. Wiri

[40]11.11. Relay ContactsThe PCM system provides a set of dual "C-form" contacts which can be used to activate external equipment. Therelay

[41]FEATURE FEATURE CODE ADDITIONAL DATA DEFAULTPrivacy Beep Inhibit 006Enable 007 EnablePre-Announce ToneInhibit 003Beep 004Chime 005 ChimeConfirmati

[42]FEATURE FEATURE CODE ADDITIONAL DATA DEFAULTEM/SCZone Group *92 Zone Numbers All CallNo Tone 020Follow Contact 0212-Second Tone 0223-Second Tone 0

[43]FEATURE FEATURE CODE ADDITIONAL DATA DEFAULTTime Trigger 2Zone Group *82 Zone Numbers No ZonesInhibit 120 InhibitEnable 121 HHMM See Note (page 44

[44]FEATURE FEATURE CODE ADDITIONAL DATA DEFAULTTime Trigger 6Zone Group *86 Zone Numbers No ZonesInhibit 160 InhibitEnable 161 HHMM See Note 3 (below

[45]13.1. Paging ZonesThe PCM system supports from 3 to 99 different paging zones (in groups of 3). It also supports up to 32 pagingzone groups for vo

[46]13.5. How To Make A Code CallCode calling is the ability to activate a series of chime tones over a signalling zone group (the specific zones in t

[47]13.7. How To Make An Echo Code CallRefer to System Programming, Section 11, for instructions on how to activate this feature and to select the typ

[48]This page intentionally left blank

[49]14. Testing and TroubleshootingFunctional Test GuideUse the following chart to verify proper operation after installation. To start the test,pick

1.IntroductionThe PCM Paging Control System (see Figure 1-1) is an expandable zone paging and signaling system. TheLUPCMALL consists of 4 pre-assemble

[50]Procedure ARefer to Figure 14-1 on page 51.1. Disconnect PCM from the telephone system.2. Set dip Switch 3, 4, and 5 to ON and 1, 2, 6, and 7 to O

Figure 14-1: Test Procedure A.[51]

[52]

Typical Connections* To Slave Amps (see Figure A-2 on page 54) * To Ambient Level Controller (see Figure A-3 on page 55) * To Call Stacker (see Figure

[54]

Figure A-3: Typical Application - Connecting to an Ambient Level Controller[55]

Figure A-4: Typical Application - Connection to a Call StackerFigure A-5: Typical Application - Connection to a Digital Feedback Eliminator[56]

[57]

[58]

[59]Confirmation Tone - A double-beep tone heard by the caller after dialing the paging access number and beforeentering the desired zone number. The

[6]1.2. Background Music• High/Low-Power distributed (buffered for up to 50 amplified speakers)• High/Low-Powered, using dedicated BGM amplifier• High

[60]This page intentionally left blank

[61]1-Amp BGM: Enabling this feature allows a single amp to provide background music (BGM) and pagingthroughout the system (BGM is lost in all zones d

[62]Time Triggers (1-8): Eight separate time-triggered tones can be programmed into the PCM. A specific zone groupcan be programmed for each time-trig

[63]Appendix D: Configuration Forms* Zone Configuration (Form D-1 on page 64)* Zone Group Map (Form D-2 on page 68)

Form D-1: Zone ConfigurationPhysical Physical Music Talk Back Night RingDescription Zone Zone in Zone in Zone in ZoneNumber Code Y/N Y/N Y/N112233445

Form D-1: Zone Configuration (Continued)Physical Physical Music Talk Back Night RingDescription Zone Zone in Zone in Zone in ZoneNumber Code Y/N Y/N

Form D-1: Zone Configuration (Continued)Physical Physical Music Talk Back Night RingDescription Zone Zone in Zone in Zone in ZoneNumber Code Y/N Y/N

Form D-1: Zone Configuration (Continued)Physical Physical Music Talk Back Night RingDescription Zone Zone in Zone in Zone in ZoneNumber Code Y/N Y/N

From D-2. Zone Groups MapPhysical PhysicalDescription Zone Zone Zones Contained In GroupGroup Code1 *012 *023 *034 *045 *056 *067 *078 *089 *0910 *101

[7]2. Before You Start2.1. Select OptionsBefore setting up your system, use the checklist below to assist you in setting up and programming the PCMPag

Figure 3-1: Rack Mounting the LUPCMALL Paging Control System[8]

[9]3.1. Adding PCMZPM ModulesThe LUPCMALL is pre-assembled to accommodate 3 zones of paging. If your installation requires 4 to 9 zones, youcan add on